Indian gold necklace design | diamond necklace design in 2020

Welcome back to imagesjewelrydesign website.

Indian gold necklace design
 Necklace design 
        

 To make the Birthstone Necklace, you're goingto need some birthstone flatback gems. 


These are Swarovski rhinestones in 4mm. And then you'll need a pendant blank to putthem on, and our pendant blank is rose gold and it's 5mm by 35mm. It has one hole at the top so it will hanglong, this way. Then we've got this very cute heart charmthat's open. And it's also in rose gold, and it is 12mmby 16mm. We've got two jump rings in rose gold, 5mm. And we've got some chain. The chain has kind of an open loop that thejump rings will fit through. It's rose gold. And we have 18 inches of that. For tools we have chain-nose pliers and round-nosepliers. We've got some tweezers to handle our gemswith. And then we're going to use E6000 glue, andwe have a toothpick that's a special trick for applying the glue. To make Birthstone Pendant we're going toglue some flatback Swarovski rhinestones onto our pendant blank. And to do that, we're going to use some E6000glue. 

Indian gold necklace design
 Necklace design 

And I like to squeeze a little bit out ontoa little scrap piece of paper. And then I like to apply it with a toothpickto the back of the rhinestone. So to do that, the tweezers come in handy. If you try to pick up one of these gemstoneswith your fingers and hold it to apply the glue, it's very difficult. So instead, I like to use the tweezers andhold the rhinestone that way. I've got these set up in the order that Iwant them. So I've got the oldest on the top. This is the birthstone for the oldest child,this is the birthstone color for the middle child, and this is the birthstone color forthe youngest child. So cute! And I'm going to glue the bottom one first. So I'm picking up that rhinestone with thetweezers, just tilting it over, and then I'm going to take that toothpick and grab a littleE6000. You don't need much. And if you twirl it you can get rid of thatlittle glue string. And then apply it to the back here of theSwarovski rhinestone. Glue on there. And then I want to set this down right whereI want it on the pendant blank. I'm going to use the tweezers just to setit down. And I can actually use another toothpick tohold it in place because it's sticking to the tweezers a tiny bit. And if you have any glue that comes out theside, I have a tiny bit there. That comes off later.
Indian gold necklace design
 Necklace design 

So don't worry about that at all. I'm going to do that with the next one. Pick up my little rhinestone, flip it over,and then apply the glue to the back there. And this is the reason you don't want to applytoo much glue. You don't want the glue to squeeze out thesides. There's my glue. And I've got my toothpick ready because nowI know it wants to stay stuck to the tweezers as I set it down. And I'm going to center that here on the pendantblank. And then I'm going to use the toothpick topush it where I want it there. So I want it centered from left to right. And then I'm going to copy that spacing betweenthe bottom one and the middle one for the next one. And if you have more kids to do than three,you can just line them on up here. If there's just one, just put the one at thebottom. It's very pretty that way. And I'm flipping over the gemstone, our littleflatback rhinestone, and apply a little glue there to the back. And we'll want to let this glue set up fora little while while we make the next part of the pendant. The tweezers are hanging on here tight, butI'm using the toothpick here to release it, so let me center that. I'm going to make sure those are on there. 
Indian gold necklace design
 Necklace design 

Press them down. And then we're going to let that set up sothe glue is nice and tight and secure. And then we're going to turn it into a necklace. Our glue is all set up, so our birthstonesare glued onto our pendant blank. And they look lovely. If you have any glue that has squished outof the side of the rhinestone and you want to clean it up, you can just use your toothpickto kind of grab it and pull it off. It should come right off. Or you can use your fingernail to pull itoff. And then we want to turn this into a necklace. So to do that what we're going to do is puta jump ring onto the pendant. And to open a jump ring we like to use twopairs of pliers. We have our chain-nose pliers here and ourround-nose pliers. What you want to do is you want to do is orientthe jump ring so that the cut is at the top of the circle. So the circle is cut here, it goes all theway around, comes back up, and there's the cut. I've got my chain-nose pliers on one sideof that cut. And then I've got my round-nose pliers, oryou could use another pair of chain-nose pliers, I'm going to grab the other side of the jumpring. I'm going to push one side to ward the tablewhile I'm holding the other side up towards the ceiling.

Indian gold necklace design
 Necklace design 

 And what that does is it maintains the circularshape of the jump ring, but it creates an opening, like opening a gate. And I'm going to put that onto our littleheart charm. I like to keep holding onto the jump ringwith the chain-nose pliers. It's easier to handle. Then your fingers aren't getting in the way. And then I can just slide the little loopon the heart charm there into the jump ring. And then while I've got it there, I'm goingto put the end of the chain into the jump ring. This is how we're attaching one end of our18" piece of chain. And it's why we wanted to make sure that theloop of our chain would fit this jump ring. I've got both of those in there now and thento close that I can either press across with my chain-nose pliers like this, or you canuse both pliers and do the reverse action of how you opened it. You see when I press it closed now it's anice, round shape. 

Indian gold necklace design
 Necklace design 

So we've got our little charm on there. And now we want to put our birthstone pendanton the other end of the chain. We're going to do the same thing we just did. I'm going to pick up my jump ring and I'mgoing to look at it to see where that cut is. You can hold it up to the light and see thelight coming through that cut if you're having trouble finding it. I'm going to hold it with the chain-nose plierson one side of the cut. I've got my round-nose pliers, or my otherpair of pliers, on the other side of the cut. And I'm just going to rotate that a littlebit, just to create a little opening there. Keep holding onto that jump ring with thepliers. And I'm going to slide the Birthstone Pendantright on there. 

Indian gold necklace design
 Necklace design 

And then I'm going to find the other end ofmy chain and feed the last loop onto the jump ring. You can make this necklace any length youwant. So you may want to test it with a necklaceyou already have. Test the length and measure it. And that's how long you'll want your chain. And because it's a lariat type necklace, youmight make it a little bit longer. So I'm just pressing that closed. And that's how easy the assembly part is. We've got the Birthstone Pendant all madeand on one end of the chain. We've got the cute little heart charm on theother end. And then to wear it, it doesn't have a clasp,you just slide the Birthstone Pendant in through the charm and you wear it like a lariat. And that is our very pretty, great gift forMother's Day, Birthstone Bar Necklace. 
Indian gold necklace design
 Necklace design 


Indian gold necklace design
 Necklace design 


Post a Comment

0 Comments

Subscribe!

Get all latest content delivered straight to your inbox.